Posts

Chosen Solution I have a month old battery replacement I purchased for my Macbook. The battery can be at any larger state of charge, go to sleep, and then instantly report a 7% charge upon waking. Here’s a screenshot of the Activity Monitor to show the instant drop off (notice the vertical line in the battery state of charge in the bottom right): Is the battery shorting out somehow? Is it something I can repair?...

Chosen Solution Can i install an ssd in a new mac mini 2011 model with hd radeon 6630M or it’s possible only in mac mini with Intel HD Graphics 3000?? SUCESS: Notes on Installing SSD in 2011 Mac Mini hi all, I replaced the HD in my mac mini with a OWC Electra SSD 6G. Fan speed the same after; there is no sensor to worry about. make sure to remove black plastic cover off of old hard drive before pulling SATA cable out of old HD; otherwise you won’t be able to....

Chosen Solution Hello all, I would like to modify a Targus iPad Air that I really like a lot to make my iPad sleep/wake. As the cover I have purchased does not do it. I do however have a bunch of small Neodymium magnets laying around the house. And was wondering where the sleep magnets are located as I can not seem to make it sleep just by moving the magnets on the surface of the iPads front surface....

Chosen Solution I have an iPhone 5s that battery was draining very fast, this happened after using cheap iPhone chargers. I decided to replace the U2 ic, after job done, phone started, booted to IOS and worked fine. I tried to charge this and when I put cable on the phone the screen got black and phone went completely dead. I replace the U2 chip again and no sigh of life....

Chosen Solution My iPhone 5s screen cracked . its a white iPhone with a white screen . can i replace the screen with a black iPhone 5s screen? You can use any colored screen you want on any mobile phone device pretty much. And yes you can definitely use a black screen on a white iPhone and vice versa. The problem is that you need to use the same home button that originally came with your phone as the touchID / fingerprint scanner or sensor is linked to the logic board....

Chosen Solution i cannot find c2020 and FL2044 on the iphone 6 plus schematics. Need some help finding the value of this component(C2020) as i accidentily knocked it off replacing my lcd now i have a partial dark spot on the lcd. Need to replace that part. Its near the backlight filters. Any help would be appriciated. thank you. It’s on page 20 of the schematics. The problem here is that there is an incorrect version of the iPhone 6 Plus schematic floating around on the web....

Chosen Solution Hey, I replaced my iPhone 6 Plus Screen (Complete Screen= Camera, TouchID, Speaker alreadyinstallen on it). If i try to turn it on, the Apple logo shows up and than it`s Black but the Backlight is working. Than it shows the Logo that it’s charging. After couple minute the Apple Logo shows up and again the Backlight is working -> in a loop. Hope someone can help me! Thanks...

Chosen Solution Sometimes when I boot my iPhone 6 Plus, it shows the apple logo and then it goes off, shows the apple logo again and so on… Sometimes it starts after a few attemps and other times I have to force a reboot a few times with Power and Home Button to get it working again. When it starts successfully everything works fine. What could the issue be? I have the same problem my phone goes to a freeziny mode and none of the bottoms work so I have to simontainiously push both home and power a few times until it starts working wish really gets scary I only had the phone for two years and this happened every time

Chosen Solution Hey … I have an iphone 6 that wont turn on . In the past the screen was flickering and when i touch it the screen goes black , the phone starts to heat up . I open it i look at the screen and after that nothing happend iphone 6 don’t give a sign of life. After a week i put it to charge and the screen was black but the phone works ( vibrate and even my clock alarm ring but nothing on the screen) ....

Chosen Solution I have an iphone 6 that dropped in water, i cleaned the motherboard and it worked fine for a month. Then it started reboot sometimes and flashing on apple logo. I tried to restore and returns error 9. I search at google and i decide to change the U2 ic. I removed the old U2 ic chip and by fault i removed the two capacitors near this chip. Please see the photo below…...

Chosen Solution Hello, i was changing my screen after i dropped and cracked my old screen on my iphone. I ordered a new screen and put it on the phone. Turned it on. The backlight lit up black but no image. Thought it was the replacement screen so i put the original screen back on. Same thing backlight lit up but no image. Ordered a new screen and still got the same thing as before....

Chosen Solution My iBook shows a padlock, entry area and an arrow pointing to the right. Any idea on what a password should be? This showed up after putting the hard drive out of a iBook g4 into an iBook. Should other components have been switched as well. Thanks Hi! This machine has an open firmware password enabled, which is similar to a BIOS password on a PC. This is not the same as the admin password, i....

Chosen Solution how do I set the idle speed Update (04/02/2017) it is a Kodiak 700 yamaha I don’t know your model, but assuming it uses a regular valve, follow the throttle line to the engine. Where it ends, it should be attached to a lever that gives it gas. At that point, there should be a screw or nut to turn that adjusts the pull on the lever. Tighten it to increase, and loosen to decrease gas....

Chosen Solution I have charged the tablet and it starts up, but the screen then shows the lock symbol. The manual just tells you how to lock not unlock. Hi, Try pressing the lock symbol and swiping it to the right.

Chosen Solution I couldn’t find a definitive answer, but I was wondering when using mobile hotspot on an iPhone, does it utilize the Wi-Fi antenna as the sender (since it disables Wi-Fi upon activating hotspot), or some sort of other antenna, chip, etc.? Thanks. It uses existing wifi hardware.

Chosen Solution I’m dismantling my 21.5” iMac EMC 2389, to replace the hard drive. I have been unable to detach the LCD thermal sensor cable from its socket, it’s nowhere near as easy as it appears on the IFIXIT video and there is no mention in the notes about it being very difficult. Is there a trick or something I am missing? Its a snap fit but as the system ages the plastic looses some of its flex so they do get thougher to disconnect....

Chosen Solution Hi All, Just wondering how I can fix my rear bumper.. What kind of materials/tools do I need? Or is it better to replace the rear bumper entirely? If yes, is there an manual for how to do it? (just wondering if there are any hidden screws) It’s a 2017 Chevrolet Camaro (not the Caprice, was unable to select the Camaro). If a picture is required, please let me know....

Chosen Solution The other party can’t hear me when I call and I activate the proximity sensor on my phone by putting it up to my ear, they can hear me as long as I have it on speaker or I don’t have it directly against my ear. Is there a fix for this? Tried resetting multiple times Let’s see if your main microphone is working at all first: open voice memo and try recording something, you should see voice waves in the memo graph when recording and be able to play it back....

Chosen Solution My macbook pro (end of 2006 edition) died last year, the hard drive totally stopped working, i took it to the mac store and they said it was the hard drive that died, and that i need to get a replacement. So i’ve taken the hard drive out, even trying to connect it to another computer just to double check, but nope its dead for sure. so what do i do now?...

Chosen Solution Replacing fpr with adjustable fpr, do I need a fuel line tool? Mike Pease here is the way the manual describes it: PRESSURE REGULATOR REMOVAL/INSTALLATION Caution • Disconnecting/connecting the quick release connector without cleaning it may possibly cause damage to the fuel pipe and quick release connector. Always clean the quick release connector joint area before disconnecting/connecting, and make sure that it is free of foreign material. Complete the “BEFORE REPAIR PROCEDURE”....