Chosen Solution Hey, Just last night I replaced the rear casing, battery and digitiser of my iPad 4th gen. The moment I booted it up, the battery was at 26% and everything worked perfectly. I plugged it in to charge, and it dropped to 20. I left it on charge for a while, came back and found no change. I unplugged it and came back in the morning. The morning comes and I plugged it in again....
Chosen Solution My iPhone 5 battery got really hot, the phone stopped charging, and drained ridiculously fast and now will not charge or even tell me the battery is low. I got a new battery thinking that was the problem but it wasn’t so this made me think it has something to do with the charging port. Next I bought and replaced the charging port and today the phone still doesn’t charge at all....
Chosen Solution So I have had this iPhone 5s since it first launched, and the batt died last August. Got a battery replacement mid December. Problems: The phone would mysteriously die when not in use. In 24 hours it’ll for sure turn off by itself. Over night it’ll shutoff. Keeping iPhone plugged in doesn’t solve the problem, it’ll still shutdown. When around 20% batt left phone would shutoff, when plugged in will turn on again normally....
Chosen Solution Hello, i am having a bit of a problem with my iPhone 6 Plus, so this problem occurs for 2 weeks ago, and it got so warmed that the Overheating notification pops up, and i left it for a while, but for 6 hours more, it doesn’t disappear, it did when the battery ran out completely. 2 Days ago, i am having a problem with my LCD, it became untouchable, and when i go to my repair shop, they told me that the IC touchscreen is damaged, and the battery needs to be changed....
Chosen Solution Hi i got iphone 6s which is charge perfectly only one direction tried many cable (which charge ok on both direction for other iphones) i cleaned usb connector replaced flex cable all ok but still same issue I stand corrected! Found this article, you should read it. Seeing as how you have already tried other known-good cables, the problem is likely with Tristar as @benjamen50 suggested.
Chosen Solution As the ZXW doesn’t show any details for iPhone 7 A1778 I’ve tried to find a schematic but no success. I have a device with the circled component which looks like a coil to me blown up. It’s just above the intel BB_RF. Does anyone know what this component is please? Update (12/26/2018) Yes. Here is picture of the component. By comparing the two boards I’d say it should be the L1816 inductor, on PP1V8_SDRAM line, 1....
Chosen Solution Just trying to figure out if my Samsung SM - J120W has dual sims . Phonel 2016 version Hi, Have you taken the back cover off and removed the battery to check how many SIM card slots there are? According to the User Guide for a sm-J120W 2016 it only has 1
Chosen Solution I can backup the 3GS on my Mac tiger but that iTunes does not recognize an iPhone 5 for transfer. My Mac high Sierra recognizes the iPhone 5 and the iPhone 3GS but will not allow a backup of the 3GS. You’ve got two easy possible ways: - if you have a pc or a mac, you can use iTunes to make a local backup on it, then you plug-in the iphone 5 and store your backup on it....
Chosen Solution Hi, I would like to upgrade the standard 64GB SSD to something like 128GB or higher. Where do I purchase the SSD? Here’s three of them: a 180 GB, a 240 GB and a 360GB: http://eshop.macsales.com/Search/Search…. No one is selling them yet, but iFixit has pledged to sell them when they are available. https://twitter.com/iFixit/status/153501… I ordered the same kind thats in my MacBook Air - A Toshiba, but in a greater capacity....
Chosen Solution How do you know when a device needs reballing? Jaywn, reballing is usually performed to replace a BGA IC, not a device. It has become somewhat more accepted to reflow devices like PS3 XBox etc. Most of the time a reflow is based on generally known failures. It is the thermal cycling that causes the following in Lead-Free Solder over time. Weak bonds Solder Voids Organic Matter Build Up Cracking Brittle Joints “Black pad” caused by the formation of brittle intermetallic layers Pad cratering, It is the space left vacant when a BGA ball pad lifts off the board....
Chosen Solution Hi, I recently repaired an iPad 7 and when I was done I noticed a bit of fingerprints and a bit of b7000 glue on the lcd so I tried to clean it using a microfiber cloth but that didnt work. I was wondering would it be possible for me to clean the LCD with 99% IPA on a paper towel or would that damage the display. I know its normally fine if it touches electronic parts but I dont know about the LCD as im not sure if it has a protective coating and/or if the IPA will seap into the LCD and leave a liquid mark on the screen when turned on....
Chosen Solution Dropped my phone and safe mode and I tried everything it told and safe mode still on Clifton Rodenberger, Found this info. that can relate to just about any phone stuck in safe mode at the 1st link below, which has more good info. you can read. If you turn on your phone without trying to activate Safe Mode and it seems to boot into safe mode no matter what you do then chances are one of the physical keys on your phone is defective or malfunctioning and is stuck in the pressed down position....
Chosen Solution Need to replace rope start. 3 nuts holding rope start are not releasing and bolts are turning with nuts. Model PH-XT675-2011 Jim, not quite sure where you are stuck. Attached image shows the individual parts for the top cover. Also, take a look at this decent video on here The service manual describes it as “Remove Engine Cover Insert (if equipped) and Cover NOTE: Whenever possible, an impact wrench should be used to loosen nuts securing retractable starter....
Chosen Solution The blower motor quit for the air conditioner and heater need information on how to replace it lovely24fan not that I doubt you or anything, but before you replace the blower motor you do want to check the blower motor relay and the heater blower transistor. Your Honda is known to have issues with that. If you want to test it use these instructions Honda-Element-Blower-Transistor.pdf Here is the location of it...
Chosen Solution The smartphone is five years old. And this year, I started to notice that the smartphone on the left side started to swell. Please help with this. And advise where to buy a battery for this smartphone.
Chosen Solution Hi everyone, does anybody have already repaired by itself the front and back glass of the Huawei Honor 6? Thanks all Hi, yes i have repaired it. Its not hard, but i used a complete display assembly and not only the glas… you can easily find a video instruction on youtube.
Chosen Solution okay…..my ipod says disabled connect to itunes but i dont know how to enter my pass code if i cant get into it please help me ??????????? makayla, there are plenty of answers on here for the same problem:) Since I am not sure what you have tried thus far, here is a copy of my answer to this question: “there are a few ways that you can try....
Chosen Solution So I left my phone on top of my car hood and then I forgot I left it there and it dropped while I was driving. So when I picked it up it was all cracked up and everything. The screen doesn’t work but when I put it to charge the little blue light from the top left corner came on . So my question is I don’t know if it can still be repaired or not....
Chosen Solution I have a problem with the screen do you change the screen or programming . It’s the screen that’s gone bad, not the software. I had an old 3GS with the same problem. My one was destroyed because water condensated inside. You should replace the whole screen modual (lcd, touch display, etc.etc).
Chosen Solution I can’t read the polarity on my coby mid9742 The paint has worn off so its hard to read and I got a universal charger to charge it but I want to set polarity right. can anyone help me? Hi, Your adapter needs to be set at 5V DC +ve centre pin of plug. Here is an image of the power port taken from your tablet’s user manual. You will see that it shows the +ve as being in the centre and the -ve as the outside of the DC plug....
