Posts

Chosen Solution The beadings of my speakers are porous and tearing apart. I’d like to switch these, because apart from that they’re still in good condition. Unfortunately I don’t know how to open the speakers without damaging them. They got no screws or similar on the back side. I contacted the Logitech support but they won’t help me due to “security reasons”. I think they just want me to buy a new Logitech system....

Chosen Solution I’m helping a friend fix his M5-581t laptop. It could be turned on but then it would shut down unexpectedly after a few seconds. At first, I though it was either the AC adapter or DC jack. Both of these were tested and replaced. I also did test where I removed the RAM, 20G SSD, Hard drive etc. I have been able to keep the laptop on by briefly shorting it on with the power button flat ribbon cable and then disconnecting it....

Chosen Solution I need a way to fix my 2011 11" Mac Air, the hint seems to be loose and I can’t stand it. Does anyone know how to tighten the hinge??? Open the cover and look at the teardown, I think after you get past the pentelobe screws, you will get hit with T5 screws Here is the teardown MacBook Air 11" Late 2010 Display Assembly Replacement

Chosen Solution Hi, My one year old htc one M9 used to work fine, until a day when it discharged and went off (because of no charge). I recharged turned it on but it ended up stuck on the htc start up logo. I thought it was a hardware issue so I took it to a technician who tried to flush but they couldnt get it working. Instead the phone now starts up to the bootloader with these infos: Software status: Modified**** LOCKEDS-ON Security Warning***** ……....

Chosen Solution I reset my galaxy note2 and after, some functions ha e not been working: can’t connect to my pc through USB, can’t get off factory mode: my phone excessively overheats, i can’t put a lock or pattern on my phone. this video may help https://www.youtube.com/watch?v=00ip2JXz…

Chosen Solution changed radios and need the code before it will work. LINDLE, it would really help if you tell us what model your Honda is. In the meantime give this a try: Hit to insert another list item, and twice in a row to end the list. To get subitems, repeat the bullet character once for each level of indent you want (e.g. ##)Turn car to ON II(radio powers up)Hit to insert another list item, and twice in a row to end the list....

Chosen Solution I replaced the trackpad. everything works fine except the touch. Have to press very hard to use the touch It sounds like you over tightened the click screw. Go back to the MacBook Air 13" Mid 2013 Trackpad Replacement guide and review step 10. Richard, Inside the macbook air where you replaced the trackpad there is a screw (bottom-middle of this image ), you may need to adjust this to change click pressure....

Chosen Solution i have a whirlpool side by side ed5lvaxwb02 i just bought my freezer works great my fridge side doesn’t get cold enough its all most there but wont reach the highest leavel Cause 1 The Evaporator Coils are Frosted Over The defrost heater assembly turns on a few times throughout the day to melt away any frost that may have accumulated on the evaporator coils. If the defrost heater assembly is defective, frost will continue to accumulate on the evaporator coils, and the coils will become plugged with frost....

Chosen Solution Hello, I own this iMac: iMac 21.5" 2.7 GHz i5 (Late 2012) After having a HDD failure I’m planning on replacing it with a SSD (Samsung SSD 850 EVO 2.5" SATA III 250 GB). Since I’m opening the iMac to replace HDD with the SSD, I would like to also upgrade my RAM. Presently I have 2x4 GB (1,5V) and want to install 2x8 GB modules. Apple’s TN on RAM Configurations used in iMac late 2012: iMac (21....

Chosen Solution Hello all, This is the Logic Board of my iMac. 820-3302-A I’d like to know what has blown here if anyone can help. Capacitor ? Fuse ? Part/Item number ? And most importantly, can it be fixed, or do I need a new/replacement Logic Board. All help is appreciated. Thank you 2012 iMac EMC 2544, 3.1GHz Intel Core i7-3770-s, Fusion Drive with 128GB SSD. @sponge_bob that is reference designator L9100 which is a 250ohm ferrite bead....

Chosen Solution my iphone is dead , I accidentally have connected 12v power supply for 5 seconds. the phone was still alive. I gave it some minutes to recover. then I turned off. after replacing the charging port flex cable the phone still won’t charging or turn on.(I don’t know if it is not turn on because my power button was already damaged before. so it is useless.). what do you think?...

Chosen Solution my iphone 6 is not detected by any PC or Mac, i have tried to connect with more than 4 pc but it is not recognized by any of them nor charge from any PC and other iphones are detected by those PC’s, but my iphone 6 is charging from charger. i tried to change the port of my iphone but still it charges from charger but is not detected by any PC....

Chosen Solution Greetings, It seems that my Creative Vision M battery has died and I’d like to replace it with new one. Any advice how I can do that? Thanks! Hi, Here is a link that shows how to replace the battery in your Creative Zen Vision M https://www.youtube.com/watch?v=akJDRpx6… creative zen vision ‘M’ Model # DVP-HD0004 (sometimes listed as DVP-HD0003) Battery Model # LPCS285385 Part # BA20603R79914 49 x 4 x 86 millimeters You can find replacement batteries, on amazon....

Chosen Solution I have an old iBook G4 that i want to give to a friend. I’m trying to just erase everything i have on it a fast way without having to reset everything to default and intensively deleting every document. Is there an easy way? I have heard that i could reinstall my OS X. I have Tiger or 10.4 installed on it, but only know where the install discs for Panther 10....

Chosen Solution Charging port is loose. Charging very slow Hi @devilwoman2018 , The USB connector is mounted directly onto the systemboard. As it is a SMD (surface mount device) type component, you’ll need SMD soldering skills and tools to carry out the repair. It is not a job for novice repairers. Here’s a link to the ifixit Motorola Moto G6 Screen Replacement guide. It is useful as it shows how to open the phone so access to the connector is possible....

Chosen Solution How much will it cost to get a Motorola G screen fixed? It still works. It’s just that the screen is cracked badly! Shi, the display assembly is around $80 and you can repair it yourself. Check on here for a decent video. Hope this helps, good luck. If you just need the glass replaced you can get a kit in on line for about $11. Where I live in Florida it is $50 labor if you provide the glass....

Chosen Solution I bought a power button flex cable but it is not connected to a hinge and all other ones in tutorials are so I am wondering how I can connect the flex to the hinge This is one of the most frustrating repairs. The easiest way to do it, which is basically impossible, with out the proper tools, is to remove the post, put the “hinge” (good word, I don’t have a word for it yet) put the post back in....

Chosen Solution Hi, I have been reading through this site and it is very very good and I like but.. I can’t seem to find the repair for a screen for a normal Xperia X10 (not a mini) Please help… Ali Wannous, I uploaded the complete service manual including service videos, schematics and test instructions for your phone to my fileserver. Do feel free to download it available here It is a rather large file so I hope you have a good connection....

Chosen Solution So my laptop is thin so in order to fit a RJ45, it’s entrance is expandable and by using it normally, it broke both in half and the two little wings that hold it in order to not fall, so i used some tape and it works but it’s inconvenient is there any way to reattach that to the laptop? it’s separate in two and the things that hold it in broke in one of the sides....

Chosen Solution I had a YLOD problem. Before I eventually fixed it, I made the mistake of going into the blu ray drive and pulling out the disc that was stuck inside. I think that this screwed with the ability of the drive to draw in discs like it normally does. What steps should I follow to properly reset this and get it to take in discs? I have done the method where you unscrew one of the gears and that snaps everything back into place, but that doesn’t seem to be all that I need to do....