Posts

Chosen Solution Hi, I´m trying to repair an iPad air presenting ghost touching. I opened it up in order to fix the problem and found digitizer flex cable to be unfold and unglued. Is it possible to re-glue it and fold it back? Pictures: https://imgur.com/a/PE9EVO7 It can surely be done although I can’t remember if the digitizer cable is glued to the glass in original screens..I checked a couple screens I have around but I found them all unglued....

Chosen Solution I am getting this error message Shooting is not possible due to an error I need help please. Hi! The following text has been quoted from the Canon forums, someone had a similar issue and this is what the rep answered: “Err 30” indicates that malfunctions related to the power source have been detected. Please follow these steps to attempt to resolve the issue: Remove the battery from the camera....

Chosen Solution There no apparent screws or fasteners, so I believe it is ‘plastic snap’ lock. This drive has intermittent power problems and I believe ‘something’ is loose inside, or I will put the drive in another case (hopefully, at worst). Regarding the power problem, sometimes when it fails, a light tap on the case makes it power back on. Here’s a guide you can follow to open the case....

Chosen Solution I work near very sensitive equipment and wifi and Bluetooth interfere with our measuring devices. However, we need to take extremely high quality videos of our work so GoPro HeroPlus is great. We must physically and permanently disable the wifi and Bluetooth. Any help is greatly appreciated. The other camera is the GoPro Fusion 360. We need to do the same with that camera. Thanks. Jim Hi @corkgiants , Have you checked in the camera’s settings menu area if turning off the WiFi/Bluetooth is an option, you didn’t say?...

Chosen Solution Hi everyone! A while ago I inserted the dummy card in my laptop’s card reader slot, but it got stuck. Any ideas how to get it out the slot, so I am able to use the slot? Thanks! Andrew Update I have tried it several times, but I am not able to get the needle to the end, because there is not enough space. Even with a second pin I am not able to get it out of the cardreader....

Chosen Solution I am trying to fix my 1st gen iPhone that I just bought as non working. It seems that the battery is bad, but I want to make sure that it’s really the problem before ordering one. Whenever I tried to restore it in itunes or 3utools, it always tried to reboot and just turned the screen off every time. Sometimes, the backlight would turn off and a ghost of the screen could be seen for a few seconds....

Chosen Solution My iPod says it is disabled and to connect to iTunes, but when I connect it to iTunes it says I need to unlock the iPod before I do anything. I’m confused. This problem has been going around for quite a while, Heres what you must do, However, be aware that this process will erase all data on your iPod Touch. To fix the disabled problem, you must go into DFU Mode and restore....

Chosen Solution I ordered the plastic tool for removing the back off my Chromebook. The instructions on the iFixit page state to remove 9 screws. Mine only has 5 screws which I removed. The tool does not slide into the rim on the back to loosen it. It seems to be stuck in the corners but I don’t see any more screws. Also my model number ends in A01US not K01US but it is listed as a Chromebook 2....

Chosen Solution I can’t get the latest adobe flash player to install in IE or Outlook. I’ve updated IE to IE8. you may try this : in IE8 go to Tools -> Internet Options -> General -> Delete Download the offline installer Close IE8 run your offline installer once it is installed reopen your browser and see if it worked. and here are people that have the same problem http://en.kioskea.net/forum/affich-83249… good luck to you....

Chosen Solution What is holding down the front glass on a iMac A1225-2211 iMac 8.1 24" Iunderstand you just remoce the glas by lifting it up. looking to find out what holds the glass in place and where the contact points are? Ron.neufeglise@ctv.ca I just used a couple of suction cups that were holding our soap dish to the shower wall. There is a guide at iMac Intel 24" EMC 2267 Glass Panel Replacement....

Chosen Solution Last week I replaced the LCD on my iPhone 4 with a Complete LCD Screen Assembly that I purchased at www.chinaontrade.com. After replacing the LCD, my iPhone 4 works great again, except for the battery life which runs empty very quickly now. Did I do something wrong, or could the battery drainage be caused by the new LCD? Regards Erik. If there isn’t much drainage in Airplane mode, then it does sound like the battery drain is due to antenna issues....

Chosen Solution Hello everybody! So I have this issue with my iPhone 6. It doesn’t recognise the charger when plugged in, but suddenly turns on with 1% battery only. During these few minutes it is on, it still doesn’t recognise the charger nor it charges. So it basically dies again to charge to 1%. This goes on and on. Do you maybe have the same experience? It is out of warranty therefore “bring to Apple” answer do not help :/ Thank you!...

Chosen Solution My iPhone 6 screen is on the fritz, it has a mind of its own. It will randomly start scrolling and tapping really fast. It’s almost like there is moisture under the screen, but I know there isnt. This problem has gotten worse over time. Maybe just a dud screen? Has anyone else seen this and how can I fix it? I’d rather not replace the screen if I don’t have to...

Chosen Solution Calling on the wisdom of the iFixit Community, I have an iPhone 6 that was dripped on, it turned on and then no longer did ( I didn’t this..the owner of said phone did. I know better than to turn on a water logged phone before drying it out). It was put in rice for a couple days, I pulled the logic board, and put it back and replaced the battery....

Chosen Solution I’ve a slightly more than 1 year old MacBook C2D. While cleaning it with the Apple supplied polishing cloth one fine day, I didn’t notice there was some stuff on the screen or on the cloth that left a nasty line along with my wiping direction. On top of that, my keys are also leaving some marks that cannot be removed. I’ve tried a few brands of LCD wipes so far....

Chosen Solution i didn’t drop it in the water i bought a new screen and lcd when i broke my old one. i put the new screen in and when i press on the srceen it looks like water marks inside the srceen i thintk it migt be oil. i washed it with 91% isopropyl alcohol i think i might’ve made it worse. Can you send the screen back? It look to me there is air between the screen and digitizer....

Chosen Solution How do I loosen the belt tighter? A lot of time the belt tightener will seize up and not move . if this happens take it off the truck and put it in a vice spray the living daylights out of it with your favorite lubricant (WD 40) or whatever and work on getting it to move once its moving freely return it to the truck and replace your belt....

Chosen Solution My model is the A1493 and I have tried finding the power pads or the pins 5 and 6 but I have no idea where they are. Pictures of my logic board: imgur.com/a/2mt9N Stanley Cheng this is the location for your power-on pads. The keyboard pin you are looking for is 5, not 6. The way your board is located in your images it will be the fifth pins from the right....

Chosen Solution I’ve taken apart a broken 3DS, and have fixed several problems with it. One that I can’t without further parts, however, is the button receptors on the motherboard. I’ve seen some on sale, and want to buy them. However, I’m unsure how to remove the old ones safely. I’ve carefully picked at them to see if they peel off, but they seem to be on there pretty hard....

Chosen Solution I dropped my phone and I’ve cracked my computer like this before. I need to know how much it would cost at a phone repair agency. I won’t fix it DIY. Depending on where you live and have insurance. It ranges from $35—$115 usd