Chosen Solution I have been trying to find a helpful guide to remove the dash from my 2001 4 -door Sunfire. I want to access the radio and AC. I am looking for a very thorough walk-through, I need to be able to dismantle the dash and put it back together in as little time as possible. I can’t be without a car because a step was skipped. Thanks gatewaynomad, take a look on here
Chosen Solution Can anyone please let me know if the wire is soldered to the battery in the pictures attached below. If it is not soldered then how is it connected? I would like to know how to remove and replace this 3.7v 1200mah rechargeable battery of my flashlight. Thank you very much! Hi @easyfixer , The wire is soldered to the battery but it is better if you just cut the wire as close as possible to the battery and then get a 18650 3....
Chosen Solution the flash of my Nikon doesn’t work. In the shop they told me it was the chip that command the flash. How can I change the flash circuit? hrguedes Here you can find teardown guide which will help you to find falsh driving circuit (see step 14 to 17) Caution : capacitors may having charge and make sure they are discharge before touching flash drive
Chosen Solution how to repair iphone 6s from salt water damaged? Salt water damage is the worst and the likely hood of saving the device is almost nil. Still, if you value the data on the device, I would suggest you do the following ASAP if you can’t get it to a professional immediately. Open your phone and remove the logic board (follow this guide)Inspect the logic board, especially around the connectors and look for corrosion....
Chosen Solution hello everyone. after changing the rom and install slimkat rom my battery doesn’t charge more than 35% and it drain so fast. I change my battery but it doesn’t change. how to fix this issus? I found out what happened. a kid just play with on/off button of lights and it ruined our charger adapters ( we have 2) and they can’t charge correctly.
Chosen Solution Can’t remove the front because of the screws? How can I remove the other two hidden? are you talking about the 2 small stickers? here is a good guide http://www.youtube.com/watch?v=vRjC19j2m…
Chosen Solution Does anyone know of a guide for how to remove and clean a Mass Air Flow sensor on a 1996 Cadillac Eldorado LTD? @mayer , Mayer, not excellent links but they may help in the removal and cleaning of your Caddy MAF sensor and the throttle body just in case it looks grungy. ((( Use only sensor safe cleaners on the MAF)))and you will see some very fine wires inside the MAF, do not touch them only spray with the cleaner, the wires are fragile....
Chosen Solution Hello iFixit Members, I ended up taking off the little connector on the logic board that seats the right speaker it was so delicate that it just ripped off. How can I resolder the cables from the speaker to the logic board. Its either the top two close together solder points or the spaced out bottom two. Please and Thank You Here is an image on the area that i am referring to....
Chosen Solution My projector was working fine (lamp has only used 79 hrs) I switched it off, then 30 mins later started it up again, power came on, tilt working, but no light from the lamp. It then shut itself down and the lamp cover indicator lights up. No warning of any kind before this happened. I have removed the lamp, but it dose not look as if it has blown!...
Chosen Solution My laptop won’t boot up sometimes and shut down immediately after a few fan noise when I press the power botton. Sometimes it boots up after I keep the laptop for a while and plug the charger in when I press the power botton. sometimes, usually when I restart my laptop, there is 5 long blinks followed by 3 short blinks with blank screen. And when I kept in this state with the charger plug in, after around 24 hours the blinking will go....
Chosen Solution The phone keeps telling me to scroll down to answer the call, but nothing happens. I can’t answer any calls. When you slide down, does the phone call continue but the line is dead, or it just wont let you complete the swipe? If you are getting a dead line try shutting off the phone and re-seating the sim card. ZTEAnswering ISSUE SOLVED HERE!! Here is the LONG AWAITED ANSWER TO YOURZTE ANSWERING PROBLEMS....
Chosen Solution I have a AF0 code on my kenmore, How can I fix this problem? The code AF normally indicates that the control senses a restricted air flow on most models of Kenmore Elite dryers. Without your model number, I cannot be sure. To clear the code, press STOP once and the estimated time remaining countdown should return to the display. The AF code will continue to appear with each cycle until the low airflow condition is resolved....
Chosen Solution the switch looks fine, there is no damage that is seen and the joy con also has no cosmetic damage that I could see, it just feels loose and falls off randomly. the switch is a limited edition switch that has a ACNH back casing and I would like to try to keep the back casing and casing for the right joy-con, if a replacement casing is needed. The switch works fine and and the only problem is the joy-con slipping off...
Chosen Solution I cracked my iPhone screen 2 weeks ago, but I don’t know how. I picked it up from on top of my backpack and it was shattered. The screen worked “perfectly fine.” However, last week, my screen began to not work for periods of time. I’d wait a minute, and it would work, only for it to shut off again a few minutes later. The display worked perfectly and Siri worked, but the screen could not detect my touch....
Chosen Solution I own a Maytag bravos quiet series 300 dryer it trips the breaker switch when I hit the power button it comes on for like one or two seconds and then it trips the breaker switch what is the problem I own Maytag bravos quiet series 300 when I hit the power button the dryer turns on it’s quiet for one or two seconds then it trips the breaker switch in the breaker box what is the problem
Chosen Solution I just recently replaced iPhone screen but with a different color home screen now it was working now it completely blacked out Did you disconnect the battery before removing the screen and connected it back only after the replacement LCD was in place? Forgetting about the battery can cause the backlight circuit on the logic board to get damaged. To be certain, shine a bright flashlight on the screen immediately after connecting the iPhone to a charging device....
Chosen Solution I want to max out the RAM on this machine, the specification says the following: RAM / Max RAM 512 MB onboard DDR2 533 MHz SDRAM single channel with onboard SDRAM and one soDIMM slot, with up to 1 GB/1.5 GB using one 512 MB/1 GB soDIMM module The machine when I check my PC general says it has 0.98GB. My question is what do I need to buy from you in order to maximize the RAM on my Acer ZG5?...
Chosen Solution I am replacing the battery in my iPhone SE with an iFixit kit. The battery appears to have the adhesive strips already attached to the back of the battery. There is the pink plastic cover with a tab at the top, but no evidence of the blue cover that they talk about in the repair guide. The strips seem fairly securely fashioned to the back of the battery. Do I just peel the pink off and install the battery?...
Chosen Solution I bought an old iMac for $50 a week ago and have been trying to figure out since what’s wrong with it. None of the diagnostic LEDs light up when the power is connected to the computer. I have tried two separate power supplies, both of which show the same issue: no pin, when measured relative to ground, shows any output voltage. I followed the voltage chart here, but no pin shows anything on either power supply....
Chosen Solution I’m deciding to buy a new iMac 5K retina display and I asked a few questions in Apple community and now I am really worry about it as people saying iMac are sealed and cannot be repair or replace anything except RAM. Because I am thinking about a long term usage like 10 years. Does it last long? I am using my MacBook Pro mid 2009 for 6 years already....
