Posts

Chosen Solution I bought a galaxy s8 and it is frp locked.. It is the Canadian version (SM-G950W) and I have tried everything but it’s not working, any help would be awesome The way I did it was download the combination file and flashed it with the modified odin and then it takes you to binary mode and you can access settings to turn off USB debugging. After you do that flash the stock rom of the same model of phone and then it’s done....

Chosen Solution Hi, my battery lid crack, the whole lid, not just the lock, is there a guide on how to fix it? Hi, Here’s a link to a video that shows how to completely dis-assemble the camera. At 6:29 minutes into the video the section containing the battery cover is seen being removed from the camera. I do not know if you have to dis-assemble it that far but hopefully the video may help you to at least gain access to the lid....

Chosen Solution I have a PB G4 667 MHz which has one hinge completely destroyed after a bad repair job which cemented the two hinges to strengthen them. I want to use the keyboard/trackpad as input while hooked up to external monitor and simply remove the display assembly so I can access the keyboard and power button (screen is not stable enough to stay open; image can be seen on screen but absolutely no backlight working)....

Chosen Solution I have an old low-end ssd, i need to upgrade it to new high-end ssd https://h30434.www3.hp.com/t5/Notebook-H… Looks like it does support both. Use the below manual to upgrade it. Hope this helps! http://h10032.www1.hp.com/ctg/Manual/c05… It’s easy. I have a similar model, and I replaced my SSD. A PDF of the manual is at this link: http://h10032.www1.hp.com/ctg/Manual/c03… Go to Page 44 and just follow the instructions. Good luck, Russ

Chosen Solution Hello! I’m having difficulty with a GBC cartridge that I bought recently to repair, but so far, I’ve had no luck with it. It will boot to the Gameboy logo screen, but the Nintendo copyright logo at the bottom of the screen is always messed up. So far, I’ve attempted cleaning the contacts, but it still does the same thing. However, I’ve been looking at the board closely (and referencing other pictures of what appears to be the same cartridge) and beyond missing the battery (which should be easy enough to replace), it’s missing an odd forked-looking piece in the upper left corner....

Chosen Solution I’m just going to get straight to the point I messed up and Broke the connector that connects to the physical motherboard I don’t know what to do from this point whether to get a whole new motherboard or just try and Sauter back the old button. I was trying to fix the old antenna but in the process I broke it off in the motherboard its not in the top left it is more in top right of the phone...

Chosen Solution i was updating my mac to the newest version when i cut it off during the installation process (dumb idea i know) but when i tried to log back in it kept restarting and saying that there was a problem?? called apple support and they couldn’t help either. Do you have the original hard drive and/or hard drive cable in it? As your Mac restarts, hold down the Command (⌘) – R combination immediately upon hearing the startup chime....

Chosen Solution Hello there, I got two Nexus7. One has the LCD screen that doesn’t display anything (but it emits sound and seems to be responsive). The second one has a crack on the glass, and the touchscreen doesn’t respond when I touch it (it was perfectly working before I made the crack). Its display still works beside the touch interface. Can I use the glass of the first one with the LCD screen of the second one?...

Chosen Solution Can that cable be replaced? I’m dealing with a customer’s computer that had a tiny bit of liquid damage on that connector. I can’t see if that cable is removable. Jorge marroquin - I’ve never needed replace it and I don’t have a system to look at. But, I think it could be removable if you can find another battery to steal the cable from. The connection is on the other side of the battery board, under the insulator sheet....

Chosen Solution hi friends I just repaired a u2 ic on iphone 6 Reparation success I wanted to ask you if the original glue black on u2 ic on the picture 1 Question: what is it used for To solidify the weld ?? If so I can put uv solder mask as in picture 2 thinkss :) Mise à jour (29/07/2017) Thank you my friend for your answer then I can cover the u2 ic with mechanic uv solder mask (green color) For welding to be consolidated see picture for example...

Chosen Solution I upgrade my MacBook Pro 7,1 to 8GB (from the original 2GB). Afterwards I upgraded the OS to El Capitan (ver 10.11.6). Everything was fine and I was very happy until the other day when I was FaceTiming and my system went whacky. Screen froze with a bunch of horizontal Lines, and started beeping (one tone at 5sec intervals). I shut it down, and restarted. Now I have no display and the beeping still there....

Chosen Solution I turn the key and it does nothing, have to start car from starter Angel Starr, replace the Ignition Switch. It is behind the Lock Cylinder and is accessed by removing the two steering covers, and the lower trim cover. This procedure above is for dash mounted and column mounted as well. Hope this helps, good luck. most likely the contacts in behind the key have worn this is the part that has about 5 or 6 wires coming out of it....

Chosen Solution I have a HP Envy notebook 14-j009TX and I want to replace its battery, but I can’t seem to find a guide for it.. Is it possible to have a guide for it? @ramos here c04722798.pdfyou go

Chosen Solution It prints only ONE sheet. I have to cancel the rest of the job and send it one sheet at a time. It used to not do this, it just suddenly started doing this recently. Hi, What happens after the first sheet is printed? What OS (Operating System - Windows 7, 8.1. 10 or Mac OS X ?) is installed in the computer that the printer is connected to?...

Chosen Solution Hey guys, A year ago I bought a second hand iMac 24 inch, 2.8 320 GB SD iMac. Worked fine for a year. Last couple of days it was in sleeping mode. Today it doen’t boot anymore. No fan, no sound. When pressing the power button there is no fan speed. I red all the topics on here, and some on google, and this is what I tried already: Switching multiple power cords and outlets....

Chosen Solution Just replaced a cracked screen on my iPhone 6S Plus. Now the proximity sensor doesn’t work. A Google search says this isn’t unusual. Anybody come up with a fix? Did you transfer over the original Prox sensor or did the screen come with one pre-installed? If you transferred it, then you may have damaged the flex. You will need to get a replacement flex. If the screen had one pre-installed, it’s not uncommon for them to be defective as suppliers tend to put lower quality flexes in screens....

Chosen Solution As the title says, I had a customer bring in an iPad Pro 12.9 that will not stay on unless plugged into a charger. When it is disconected, it will power down within seconds, and all it will display is a dead battery and lightning cable. As soon as the iPad is plugged into a power source, it powers right up and displays the battery is at 100%. I have ordered a new battery for the iPad, but I have a couple questions....

Chosen Solution Hello guys! I’ve encountered a minor glitch last night when the whites of my screen turned aquamarine. Seconds after, it went back to normal. Today, as I was using my iPad my screen’s condition got worse. There’s a maroon-like sheen on the edges, colors are distorted, and some icons like the keyboard subtly show up on the home screen. I’ve been using my iPad Air 2 for 3 years now and it has been in good condition until this morning....

Chosen Solution Hello! I have strange problem with iPhone 5. When I connect it to external power source, it immediately 0.5A current for ~1sec, then nothing for 1sec, then 0.5A for 1sec and its looping. iPhone is booting normally, works for some time, then shuts off and coming back to “current loop”. Is it PMIC fault? On the iPhone 5, the charging is managed by the PMIC once the proper communication has been set via Tristar (U2)....

Chosen Solution My iphone one day suddenly turned off. At start when I tried to charge it then phone turned on, showed apple logo and then turned off and then these steps just repeated (turn on>show apple logo>turn off>repeat). I tried to connect it to itunes but it was not being detected. Only when you connect it to wall outlet it turned on and did previous steps. So I searched on internet and found DFU mode so I did that....